• Cable Requirements: 24 AWG minimum, multi-conductor stranded with an overall foil shield, for example Belden 9540 or similar. Per the SIA’s Wiegand specification, maximum cable length is 400 feet (121.92 m).
• Grounding: Shield (drain) continuity must run from the Receiver to the access panel. Shield and reader ground must be tied together at the access panel and connect then to an earth ground at one point.
• Power: Power required is 12 VDC nominal at 120mA. The Receiver may be powered by the access panel. A linear power supply is recommended for best operation. Power Supply is not included, but can be powered directly from Viking model ES-1, K-1700-IP, C-4000, AES-2000, and AES-2005 entry systems. When used with an ES-3 a seperate 12 VDC power supply is required.
• Mounting: The Receiver may be mounted indoors or outdoors. The base of the enclosure includes a drill template providing mounting provisions to a wall box (standard North American and European), as well as pre-drilled holes in the four corners allowing mounting to a flat surface.
• Read Range Adjustment: As shipped, the Receiver is set for the maximum read range, which is nominally up to 400 feet. This may be reduced by adjusting the range pot in the counter-clockwise direction. Additionally, for optimal read range it is important that the Receiver be mounted as far from potential interference sources as possible. These sources may include, but are not limited to, large metal obstructions, as well as magnetic fields and radio transmissions. Note for each installation, read range may vary.
• External LED Indicator: (Beeper Switch must be set to ON in order for the external LED to operate)
  • Amber: Normal powered on state
  • Flash Green: An activated Transmitter button press has been received and processed
  • Flash Red: A non-activated Transmitter button press has been detected
  • Off: Receiver is not powered on, or failed to power up successfully (or Beeper Switch is turned to OFF)
• Antenna Switch: As shipped, the Receiver’s Antenna Switch is set in the INT position. If a separate antenna is to be used, then the switch should be set in the EXT position.
• Beeper Switch: As shipped, the Receiver’s Beeper Switch is set in the ON position. If the installation technician prefers to disable the beeper and External LED Indicator, then the Beeper Switch should be set in the OFF position.
• 10-Pin Terminal Block: Refer to the information below for cabling to the Receiver:
  • AD0: Button One, Wiegand Data 0, Channel A (GREEN)
  • AD1: Button One, Wiegand Data 1, Channel A (WHITE)
  • BD0: Button Two, Wiegand Data 0, Channel B (GREEN)
  • BD1: Button Two, Wiegand Data 1, Channel B (WHITE)
  • CD0: Button Three, Wiegand Data 0, Channel C (GREEN)
  • CD1: Button Three, Wiegand Data 1, Channel C (WHITE)
  • DD0: Button Four, Wiegand Data 0, Channel D (GREEN)
  • DD1: Button Four, Wiegand Data 1, Channel D (WHITE)
  • GND: Power, 0VDC (Ground)
  • +VDC: Power, 12VDC Nominal

• Power: ­­­120V AC/12V DC 500mA, UL listed adapter provided or use any 12-24V AC or DC source @ 200mA (designed to share power with the doorstrike power supply)
• Dimensions: 5.25” x 3.5” x 1.75” (133mm x 89mm x 44mm)
• Shipping Weight: 3 lbs (1.3 kg)
• Environmental: 32°F to 90°F (0°C to 32°C) with 5% to 95% non-condensing humidity
• Relay Contact Ratings: 5A @ 30V DC/250V AC maximum
• Maximum Wiegand Length: 152m (500 ft) with 24 AWG
• Maximum LOG BUS Length: 1610m (5280 ft / 1 mile) with 24 AWG
• Connections: (11) screw terminals, (1) RJ-11 telco jack

* HID and the HID logo are registered trademarks of HID Global Corporation, an ASSA ABLOY company. All other trademarks are the property of their respective owners.